GPS Speed Switch

Hummingbird Electronics' GPS Speed Switch provides a simple to install, calibration free speed based switch.

Speed thresholds are set using internal switches in either km/h or mi/h.

Using data received from the Global Positioning Satellite network, the GPS Speed Switch calculates three-dimensional ground speed. If the speed exceeds the threshold, open collector outputs are switched.

This high technology solution eradicates the dependency on vehicle specific parameters, thereby reducing installation time and eradicating the need for periodic calibration.

Speed Switches have traditionally used speed-signals derived from gearbox mounted hall-effect or inductive speed senders. The Hummingbird Electronics' speed switch integrates the source of the speed signal with the switch resulting in a small, reliable solution. No calibration is required and operation is completely independent of the vehicle.

Three dimensional velocity calculations are accurate to 0.2km/h and are updated 4 times per second. A 50 channel satellite receiver, enhanced receiver sensitivity and active antenna result in fast time-to-first-velocity-calculation as well as the ability to operate in the harshest RF environments such as canyons and cities.

Last known position and satellite information critical to fast start-up are battery backed in case of power failure.

Two open-collector outputs are provided, one normally-closed and one normally-open. The normally-open one switches to ground when the speed-switch-point is exceeded and the normally-closed one goes open-circuit.

Designed for harsh automotive environments, the module features transient voltage protection on the supply and short circuit protected outputs.

GPS Speed Switch is supplied in a rugged aluminium enclosure with provision for screw mounting when required. Antenna connection for the active antenna is provided through a gold-plated threaded SMA connector.

The active antenna is available in two options:

• magnetic mount, suitable for mounting in the interior of the vehicle, for example under the dashboard or rear window sill.
• bulkhead mount, suitable for exterior mount, for example on the roof of the cab.

For optimum performance, the antenna should be mounted horizontally and upright; and should have a clear view of the sky.

A red LED is provided to give the user status information.

Power to the unit and switch outputs are provided through four colour coded wires.

• Input voltage: minimum 9V, maximum 36V
• Power consumption: 480mW (incl. antenna)
• Output current: Internal resettable fuse: hold current: 0.12A, trip current 0.39A
• Acquisition time, loss of lock: less than 2s (90% of the time)
• Acquisition time, temp loss of power: less than 10s (50% of the time), less than 13s (90% of the time)
• Acquisition time, power-up: less than 38s (50% of the time), less than 42s (90% of the time)
• Accuracy, horizontal: less than 5m (50% of the time), less than 8m (90% of the time)
• Accuracy, altitude: less than 10m (50% of the time), less than 16m (90% of the time)
• Precision, velocity: less than 0.06m/sec or 0.22km/h
• Update rate: 4 times per second (4Hz)
• RF interface: SMA connector supplied on magnetic and bulkhead antenna versions
• General: 50 channel tracking receiver, battery backup 12 days

• Size: 35mm (L), 35mm (W), 20mm (H), baseplate 51mm wide
• Antenna dimensions(mm): 51(l), 42(w), 12(h); cable length 5m

• Operating temperature: -40°C to +85°C
• Storage temperature: -55°C to +105°C
• Humidity: 5% to 95% R.H. non condensing at 60°C

• Red: input voltage (6V to 35V)
• Black: ground (0V)
• Yellow: normally-open circuit, pulls low if speed exceeded
• Green: normally-closed, goes open circuit when max speed exceeded

• SW10: ON = miles per hour, OFF = kilometers per hour
• SW9: Spare
• SW8-1: Switching speed = SW1+2*SW2+4*SW3+8*SW4+16*SW5+32*SW6+64*SW7+128*SW8

Example: speed 35km/h – SW10=OFF for km/h; SW6 = ON (32), SW2 = ON (2), SW1 = ON (1); 32+2+1 = 35 Note: If GPS lock is lost, the unit will default to zero speed

GPS Speed Switch brochure.pdf
Speed Switch Settings Rev 1-0.pdf
Warranty

DISCLAIMER

Hummingbird Electronics Pty Ltd has designed the product for use in a broad range of applications. It is however solely the customer's responsibility to evaluate the device and determine it's suitability in their end application.

Hummingbird Electronics Pty Ltd does not suggest or make any recommendation as to the suitability of parameters that determine angle, height, impact, speed, force, accident, harsh braking, roll-over or rate-of-turn events, input or output voltage or current. Parameter values stated or implied in this document are for explanation only and should not be taken as typical or representative of a real world situation.

---

USE OF PRODUCTS

Products are not authorised for use in critical safety or other applications where a failure may reasonably be expected to result in personal injury, loss of life, or catastrophic property damage. If a customer uses or sells the products for use in any such applications, the customer acknowledges that such use or sale is at customer's sole risk. The customer will indemnify, defend or hold Hummingbird Electronics and their electronic component suppliers/assemblers harmless from and against any and all liabilities and costs arising out of or in connection with use of product or sale.